# $Id: pnpdump_main.c,v 1.27 2001/04/30 21:54:53 fox Exp $
# Release isapnptools-1.26
# 
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
# 
# For details of the output file format, see isapnp.conf(5)
# 
# For latest information and FAQ on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
# 
# Compiler flags:  -DREALTIME -DHAVE_PROC -DENABLE_PCI -DHAVE_SCHED_SETSCHEDULER -DHAVE_NANOSLEEP -DWANT_TO_VALIDATE
# 
# Trying port address 0273
# Board 1 has serial identifier 9d ff ff ff ff 35 0b 63 0e
# Board 2 has serial identifier 6d ff ff ff ff f0 00 8c 0e

# (DEBUG)
(READPORT 0x0273)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING

# Card 1: (serial identifier 9d ff ff ff ff 35 0b 63 0e)
# Vendor Id CSC0b35, No Serial Number (-1), checksum 0x9D.
# Version 1.0, Vendor version 0.4
# ANSI string -->CS4236B<--
#
# Logical device id CSC0000
#     Device supports vendor reserved register @ 0x38
#     Device supports vendor reserved register @ 0x39
#     Device supports vendor reserved register @ 0x3b
#     Device supports vendor reserved register @ 0x3c
#     Device supports vendor reserved register @ 0x3d
#     Device supports vendor reserved register @ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CSC0b35/-1 (LD 0
#     ANSI string -->WSS/SB<--

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       First DMA channel 1.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed type A
 (DMA 0 (CHANNEL 1))
#       Next DMA channel 0 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed type A
 (DMA 1 (CHANNEL 0))
#       IRQ 5.
#             High true, edge sensitive interrupt (by default)
 (INT 0 (IRQ 5 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0534
#             Maximum IO base address 0x0534
#             IO base alignment 4 bytes
#             Number of IO addresses required: 4
 (IO 0 (SIZE 4) (BASE 0x0534))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0388
#             IO base alignment 8 bytes
#             Number of IO addresses required: 4
 (IO 1 (SIZE 4) (BASE 0x0388))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0220
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
 (IO 2 (SIZE 16) (BASE 0x0220))

#       Start dependent functions: priority acceptable
#       First DMA channel 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed type A
# (DMA 0 (CHANNEL 1))
#       Next DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed type A
# (DMA 1 (CHANNEL 0))
#       IRQ 3, 4, 5, 7, 10 or 11.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0534
#             Maximum IO base address 0x0ffc
#             IO base alignment 4 bytes
#             Number of IO addresses required: 4
# (IO 0 (SIZE 4) (BASE 0x0534))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0388
#             IO base alignment 8 bytes
#             Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0388))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0260
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 2 (SIZE 16) (BASE 0x0220))

#       Start dependent functions: priority functional
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed type A
# (DMA 0 (CHANNEL 0))
#       IRQ 3, 4, 5, 7, 10 or 11.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0534
#             Maximum IO base address 0x0ffc
#             IO base alignment 4 bytes
#             Number of IO addresses required: 4
# (IO 0 (SIZE 4) (BASE 0x0534))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x03c8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0388))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0300
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 2 (SIZE 16) (BASE 0x0220))

#     End dependent functions
 (NAME "CSC0b35/-1[0]{WSS/SB              }")
 (ACT Y)
))
#
# Logical device id CSC0001
#     Device supports vendor reserved register @ 0x38
#     Device supports vendor reserved register @ 0x39
#     Device supports vendor reserved register @ 0x3b
#     Device supports vendor reserved register @ 0x3c
#     Device supports vendor reserved register @ 0x3d
#     Device supports vendor reserved register @ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CSC0b35/-1 (LD 1
#     ANSI string -->Game<--

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0200
#             Maximum IO base address 0x0200
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0200))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0208
#             Maximum IO base address 0x0208
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0208))

#     End dependent functions
# (NAME "CSC0b35/-1[1]{Game                }")
 (ACT Y)
))
#
# Logical device id CSC0010
#     Device supports vendor reserved register @ 0x38
#     Device supports vendor reserved register @ 0x39
#     Device supports vendor reserved register @ 0x3b
#     Device supports vendor reserved register @ 0x3c
#     Device supports vendor reserved register @ 0x3d
#     Device supports vendor reserved register @ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CSC0b35/-1 (LD 2
#     ANSI string -->Ctrl<--
#     Logical device decodes 16 bit IO address lines
#         Minimum IO base address 0x0120
#         Maximum IO base address 0x03a8
#         IO base alignment 8 bytes
#         Number of IO addresses required: 8
 (IO 0 (SIZE 8) (BASE 0x0120))
 (NAME "CSC0b35/-1[2]{Ctrl                }")
 (ACT Y)
))
#
# Logical device id CSC0003
#     Device supports vendor reserved register @ 0x38
#     Device supports vendor reserved register @ 0x39
#     Device supports vendor reserved register @ 0x3b
#     Device supports vendor reserved register @ 0x3c
#     Device supports vendor reserved register @ 0x3d
#     Device supports vendor reserved register @ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CSC0b35/-1 (LD 3
#     ANSI string -->MPU<--

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       IRQ 10.
#             High true, edge sensitive interrupt (by default)
 (INT 0 (IRQ 10 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0330
#             Maximum IO base address 0x0330
#             IO base alignment 8 bytes
#             Number of IO addresses required: 2
 (IO 0 (SIZE 2) (BASE 0x0330))

#       Start dependent functions: priority acceptable
#       IRQ 3, 4, 5, 7, 10 or 11.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0330
#             Maximum IO base address 0x0360
#             IO base alignment 8 bytes
#             Number of IO addresses required: 2
# (IO 0 (SIZE 2) (BASE 0x0330))

#       Start dependent functions: priority functional
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0330
#             Maximum IO base address 0x03e0
#             IO base alignment 8 bytes
#             Number of IO addresses required: 2
# (IO 0 (SIZE 2) (BASE 0x0330))

#     End dependent functions
 (NAME "CSC0b35/-1[3]{MPU                 }")
 (ACT Y)
))
# End tag... Checksum 0x00 (OK)

# Card 2: (serial identifier 6d ff ff ff ff f0 00 8c 0e)
# Vendor Id CTL00f0, No Serial Number (-1), checksum 0x6D.
#     Version 1.0, Vendor version 1.0
#     ANSI string -->Creative ViBRA16X PnP<--
#
# Logical device id CTL0043
#     Device supports vendor reserved register @ 0x38
#     Device supports vendor reserved register @ 0x39
#     Device supports vendor reserved register @ 0x3b
#     Device supports vendor reserved register @ 0x3c
#     Device supports vendor reserved register @ 0x3d
#     Device supports vendor reserved register @ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CTL00f0/-1 (LD 0
#     ANSI string -->Audio<--

# Multiple choice time, choose one only !

  (INT 0 (IRQ 7 (MODE +E)))
  (DMA 0 (CHANNEL 3))
#  (DMA 1 (CHANNEL 3))
  (IO 0 (SIZE 16) (BASE 0x0230))
  (IO 1 (SIZE 2) (BASE 0x0340))
  (IO 2 (SIZE 4) (BASE 0x0398))


#     Start dependent functions: priority preferred
#       IRQ 5.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 1.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 1))
#       Next DMA channel 3.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 3))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0220
#             IO base alignment 1 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0330
#             Maximum IO base address 0x0330
#             IO base alignment 1 bytes
#             Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0330))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0388
#             IO base alignment 1 bytes
#             Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0388))

#       Start dependent functions: priority acceptable
#       IRQ 5, 7, 9 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 7 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 3))
#       Next DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 3))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x0330
#             IO base alignment 48 bytes
#             Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0388
#             IO base alignment 1 bytes
#             Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0388))

#       Start dependent functions: priority acceptable
#       IRQ 5, 7, 9 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Next DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x0330
#             IO base alignment 48 bytes
#             Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))

#       Start dependent functions: priority acceptable
#       IRQ 5, 7, 9 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Next DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))

#       Start dependent functions: priority functional
#       IRQ 5, 7, 9 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 7 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 3))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x0330
#             IO base alignment 16 bytes
#             Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0394
#             IO base alignment 4 bytes
#             Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0388))

#       Start dependent functions: priority functional
#       IRQ 5, 7, 9 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))

#     End dependent functions
 (NAME "CTL00f0/-1[0]{Audio               }")
 (ACT Y)
))
#
# Logical device id CTL7005
#     Device supports vendor reserved register @ 0x38
#     Device supports vendor reserved register @ 0x39
#     Device supports vendor reserved register @ 0x3b
#     Device supports vendor reserved register @ 0x3c
#     Device supports vendor reserved register @ 0x3d
#     Device supports vendor reserved register @ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CTL00f0/-1 (LD 1
#     Compatible device id PNPb02f
#     ANSI string -->Game<--

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0201
#             Maximum IO base address 0x0201
#             IO base alignment 1 bytes
#             Number of IO addresses required: 1
# (IO 0 (SIZE 1) (BASE 0x0201))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0200
#             Maximum IO base address 0x020f
#             IO base alignment 1 bytes
#             Number of IO addresses required: 1
# (IO 0 (SIZE 1) (BASE 0x0200))

#     End dependent functions
# (NAME "CTL00f0/-1[1]{Game                }")
# (ACT Y)
))
# End tag... Checksum 0x00 (OK)

# Returns all cards to the "Wait for Key" state
(WAITFORKEY)